Brushless Square Wave Controller 36V 48V 60V 1000W 1200W 1500W 34A 36A 40A with LCD Display for Electric Bike Electric Scooter

Intelligent brushless square wave controller for electric bike/electric scooter/brushless motorVoltage: 36V/48V/52V/58V/60V/72V universalCurrent: 34A-40ANumber of transistors: 15Rated power: 1000W-1200W-1500W all can workFeatures:1. Brake light power2. Intelligent recognition3. Low level brake4. Reverse gear5. Head light/rear light6. Hall7. PAS (pedal assist)8. Linear brake (Thumb brake)9. Regeneration brake10. Speed control handle11. Electric door lock12. LCD13. Phase line14. BatteryConnection Instructions:1. Connect the phase line color to color connection2. Connect the battery line (red wire: battery +, black: battery-)3. Connect the controller LCD line, connect ignition switch (controller 2 wires ignition switch need short)4. Connect the hall line (5 wires hall need color to color connection, if your motor hall is 6 wires, will show E-001)5. Off power, let two intelligent recognition lines connect together, open power, the wheel will forward or reverse. If wheel forward, separate the intelligent recognition line. If wheel reverse, separate the intelligent recognition line, let 2 intelligent recognition lines connect together again, if wheel forward, separate the intelligent recognition line. This function allows the controller to intelligently identify the battery voltage and adjust the rotation direction of the motor. NOTE: when use thumb throttle, intelligent recognition must separate.6. Other functions can be connected as needed.Display Functions:Speed display, power indication, fault indication, total mileage, single mileageControl and Setting Functions:Power switch control, wheel diameter setting, idle automatic sleep time setting, backlight brightness setting, start mode setting, drive mode setting, voltage level setting, controller current limit setting, USB charging functionCommunication protocol: UARTError Codes:E-001: Motor malfunction (if not connect hall wires, or connect wrong also will show this error)E-002: Throttle malfunctionE-003: Controller malfunctionE-005: Controller undervoltage alarmE-006: Communication failure, instrument unable to receive controller signalSettings Parameters:P02: Mileage unit, 00000 is km; 00001 is mileP03: Voltage rating: 24V, 36V, 48V, 52V, 60V, 72V; default 36VP04: Dormancy time: 0, no dormancy; other numbers are dormancy time, range: 1-60; unit minutesP05: Booster gear: 3 gear, 5 gear; default 5 gearP06: Wheel diameter: unit, inch; 10-38, default is 10; adjustable, precision: 0.1P07: Velocimetry: range: 1-100; default 30P08: Speed limit: range 0-100 km/hP09: Zero start, non zero start setting, 00000: zero start; 00001: non zero startP10: Drive mode set - 00000: power drive; 00001: electric drive; 00002: power drive and electric drive coexist simultaneouslyP11: Help Sensitivity Set: 1-24P12: Power start strength setting: 0-5P13: Auxiliary Magnetic Disc Type Setting: 5, 8, 12 Magnetic Steel Four TypesP14: 0 gear, acceleration does not activate throttle; default value: 1 (excluding 0 gear)P15: Default values: 0 (no cruising), 1: cruising (hold the accelerator for 6 seconds to enter the current speed cruising state)P16: ODO zero setting long press key 5 seconds ODO zeroP17: Factory resetP18: Default value: 1, locked and fixed, cannot be changedKey Operations:1. Shutdown state, long button power boot; short button power will switch between ODO, TRIP, VOL2. Boot state, long button power shutdown, short press MODE key, switch GEAR gear 0-53. Long press power + MODE key into the menu setting interface, in the P01 interface, short power key switch menu to P02, short MODE key to change the current bit value3.1 To enter the menu setting interface, in any menu state, the short key power switches the menu, the short press or the long key MODE increases or decreases the value (the long key power changes the value addition direction, the left side displays "A" indicates the increase value, the left side displays "d" indicates the decrease value), after the modification, the short key power switches to the next parameter, and saves the previous parameter value; after the parameter modification completes again the long press power + MODE key exits the setting interface, or waits for 8 seconds to automatically exit and save the parameter.Important Note: The WXGN100 monitor comes with a thumb throttle function, so there is no need to connect the throttle cable on the controller separately, otherwise an error will be reported. If you do not use the WXGN100 instrument panel, use the WXGN200 or WXGN301, which do not have a throttle function, to additionally connect the throttle on the controller.

• Brushless Controller with LCD Display: The electric scooter brushless controller and instrument set is an electronic device specifically designed for electric scooters and electric bicycles. It can control the speed and direction of the scooter and is equipped with a display instrument, making it easy for users to understand the operating status of the scooter or electric bicycle
• Brushless Design for Enhanced Performance: This set adopts a brushless design, making it smoother to use, more stable, and has a longer lifespan
• Universal Compatibility: This set is suitable for various electric scooters of different brands and models, and can meet the different needs of users
• Advanced Technology and Durability: This controller adopts advanced technology and has excellent performance and durability, ensuring the safety and stability of the scooter
• Multiple Power Options Available: The controller supports voltage ratings of 36V, 48V, 52V, 58V, 60V, and 72V with current ratings of 34A to 40A, and rated power of 1000W, 1200W, and 1500W to accommodate various electric bike and scooter configurations
• Comprehensive Feature Set: Includes intelligent recognition, brake light power, low level brake, reverse gear, headlight and rear light control, hall sensor support, pedal assist system, regeneration brake, speed control handle, electric door lock, and LCD display functionality
• Multi-Function LCD Display: Features speed display, power indication, fault indication, total mileage tracking, single mileage tracking, power switch control, wheel diameter setting, idle automatic sleep time setting, backlight brightness adjustment, and USB charging function